|
The plug used to connect wiring to Mk2 alternators. Use this when upgrading from a Mk1 type along with the later bracket.
Also replace the plug with ...
|
|
|
|
Price: £5.02
|
 |
|
|
|
Mark 2 Alternator Bracket most commonly required when upgrading from a Mk1 11AC to a MK2 18ACR. The 11AC has a larger body than the 18ACR hence the d...
|
|
|
|
Price: £10.00
|
|
|
|
|
High Tensile Bright Zinc Plated bolt for mounting the Alternator in its original factory location. The bolt is a little long but sufficiently threaded...
|
|
|
|
Price: £4.79
|
|
|
|
|
UNF Bolt for attaching the starter motor to a Car with automatic transmission.
Also known as BH606181. High Quality tensile steel marked 8.8
Two re...
|
|
|
|
Price: £1.14
|
|
|
|
![Coil Set Screw [SH505051] UNC HU855](shopthumbs/280.jpg)
|
Set screw in zinc plate, 5/16UNC, two of which are used to fix the Coil Mounting Bracket and Ballast resistor where used.
...
|
|
|
|
Price: £0.53
|
|
|
|
![Distributor [Distributer] BasePlates Set 520127-8](shopthumbs/735.jpg)
|
Baseplate set for Lucas Twin points Distributor.
Excellent purchase for anyone with the no longer available Piranha set up and needing a new Lumeniti...
|
|
|
Price: £40.66
|
|
|
|
![Distributor [Distributer] O Ring 517913](shopthumbs/38.jpg)
|
O ring that fits on the Distributor shaft...
|
|
|
|
Price: £0.28
|
|
|
|
|
Fan and Pulley to go with the Alternator GXE2297
...
|
|
|
|
Price: £27.23
|
|
|
|
|
10 Amp Glass Fuse Used for Dip Beams Side and Tail lights, and other general lighting...
|
|
|
|
Price: £0.30
|
|
|
|
|
15 Amp Glass fuse used for Wiper Motor Circuit...
|
|
|
Price: £0.25
|
|
|
|
|
Glass fuse 2 Amp used for the Radio in line fuse. ...
|
|
|
|
Price: £0.25
|
|
|
|
|
25 Amp Glass Fuse used in the Heater and Main Beam Circuits...
|
|
|
|
Price: £0.25
|
|
|
|
|
35 Amp Glass Fuse used in the Battery Control and Igniiton Control Circuits
Some of tthese have coloured paper inserts...
|
|
|
|
Price: £0.25
|
|
|
|
|
Glass Fuse 5 Amp Parking Lights ...
|
|
|
|
Price: £0.25
|
|
|
|
|
50 Amp Glass Fuse. Incorrect Application. We only use this to protect a 16 inch Kenlowe Electric Cooling Fan wired from the main fuse box. For this a...
|
|
|
|
Price: £0.25
|
|
|
|
|
Fuse Kit for Standard Car with Overdrive comprises
GFS3002 Fuse 2 Amp x 1
GFS3005 Fuse 5 Amp x 1
GFS3010 Fuse 10 Amp x 5
GFS3015 Fuse 15 A...
|
|
|
|
Price: £4.65
|
|
|
|
|
Screw for mounting ignition module to base plates No 10 x 1/4UNF
Not normally required as the existing screws are used, or the module is supplied alr...
|
|
|
|
Price: £1.72
|
|
|
|
|
Jam or Lock Nut 9/16 UNF for retaining pulleys on the Mk2 18 ACR Alternator and the power steering pump pulley when a nut is used.
...
|
|
|
|
Price: £0.53
|
|
|
|
|
Oil Pressure Switch with three terminals for USA Models from LE20000
Made in UK...
|
|
|
|
Price: £24.75
|
|
|
|
|
Pre-insulated Blue Ring terminal 8mm or 5/16 Hole
The Pre-insulation is designed to be crimped twice, once on the centre of the narrow portion to al...
|
|
|
|
Price: £0.13
|
|
|
|
|
Screw that holds the condensor to the topmost Distributor baseplate.
Very difficult to install in situ. Removal of distributor is advised.
Use the ...
|
|
|
|
Price: £2.55
|
|
|
|
![Set Screw UNC [aka SH506101] HU960](shopthumbs/281.jpg)
|
High Tensile 3/8 UNC Set Screw in Zinc Passivate or Bright Zinc Plate also known as SH506101
Used for Exhaust Manifold attachment and Starter Motor o...
|
|
|
|
Price: £0.87
|
|
|
|
|
High Tensile 1/4 UNF Zinc Plated Set Screw for attaching Rear crank seal plate.
Also used to fix Distributor in place
Further this item has a funct...
|
|
|
|
Price: £0.33
|
|
|
|
![StarterSolenoid Montego Maestro Rover 82 on [BAU5780] AEU3029R](shopthumbs/1014.jpg)
|
Solenoid for Starter Type LRS278 in the rare case one of these is fitted to your Stag.
Also fits most Montegos,Maestros, Rover Saloon from 82 and ea...
|
|
|
|
Price: £29.70
|
|
|
|
|
|
Pay this surcharge if you wish us to send out a reconditioned unit before receiving your old unit.
This surcharge will attract VAT
On receipt of y...
|
|
|
|
Price: £528.00
|
|
|
|
|
This Temperature or Thermal Transmitter used in a Stag will give a vertical needle at 90C just like a modern car.
We have to charge a small parcel r...
|
|
|
Price: £10.39
|
|
|
|
![Vacuum Advance Retard Tube Elbow [128262] 12B2062](shopthumbs/810.jpg)
|
Elbow for connecting vacuum Advance Retard tubing to Distributor or Carburettor.
...
|
|
|
Price: £2.90
|
|
|
|
![Vacuum Advance Retard tube Straight [12B2095] :131211](shopthumbs/854.jpg)
|
Straight Rubber Vacuum Advance and Retard connector
...
|
|
|
|
Price: £0.74
|
|
|
|
|
This is a 50 cm length of Black Nylon 1/8 th OD Vacuum Advance/Retard tubing for customers to cut to length as necessary.
We can cut to an exact len...
|
|
|
|
Price: £0.51
|
|
|
|
|
These 14 inch refills are suitable for installation in original centre hinged Trico speedblade wiper blade frames or SOCTFL funded replicas. They are ...
|
|
|
Price: £11.34
|
|
|
|
|
Carbon Brush to fit Wiper Motor. Three pieces are required of which one may need a little alteration with a small knife.
The High cost is in part due...
|
|
|
Price: £12.03
|
|
|
|
